Forumsee logo
Forumsee » Radio Control (RC) » Technical & Components

Technical information, batteries, engines, control devices...

1 2 3 4 5 6 7 Next >>   25 50 75

Today

I have a Scorpion 4035 500kv motor in an Assault 700 heli with 121 tooth main gear and 12 tooth pinion and an all-up weight of 11.8lbs using 690mm blades. I fly at 1720 head spe...
Hi Guys, I bought these two "R617FS" 7 channel FASST receivers from an eBay seller last week. I received them in the mail and found the graphic to say "made in China" on t...
this forum is with the purpose to start discussing this product and having an index on 1st page, so any frequent question will have the answer there so no need to ask it or seac...
Analog IC based servo tester with ground based input voltage,adjustable range and centre. I originally posted this here, https://www.rcgroups.com/forums/show...2#post376107...
Please help. So confused. First the usual background. I am returning to the hobby after a 22 year absence. At that time, NiCd's were it and only it. Now there is multiple batte...
So I bought the vx1e. I'm trying to update the firmware and I follow the steps and everything is fine except when I do what they say: Update success disconnect and power off....
I think i encountered this issue a few years back but forget what the real solution was.. I have lipo balance boards connected to the reaktor.. I have a nano-tech single s...
Well I have. Just got a new battery with EC5 connector and didn't look at it. Plugged it into my MPA parallel board with 4 other batteries already on it and zap. Tripped one...
Hi for all Please, an question, I have the Revolectrix PowerLabs 6 and the place that I fly doesn't have electricity to charge again the LIPOs. I wanna to charge one 3S CEL...
I have a 6s battery that the balance connector got damaged in a crash and I need to know how to discharge it so I can dispose of it. I usually use auto headlamp bulb on m...
Rather than using one of my chargers to take a fully charged 6s lipo back down to a safe storage charge, will it be safe to use this 24 volt, 250 watt halogen bulb to bring the...
Hi all, I think the title is self explanatory. Can anyone help me? I have Channel 8 SWD set up in beta flight to activate the lost buzzer when fliped, and it works fin...
Hi all Having trouble trying to get the programmer to work. Connects to the computer but when you connect it to the servo it only stays connected for a few seconds then says ...
My turnigy 9xr pro is not turning on. i tried to connect 2200 mah 5c 3s lipo. I charged it fully. I checked circuit voltage, fuse , switch though those are good but its not tu...
Can one of you engineering types explain to me why my 3 radios use 3 different voltages of batteries. A Futaba uses a 6v 1800 mah A HiTech uses a 7.4 v 2200 mah A Graupne...
A flying buddy has a JR transmitter that will not turn on. I have agreed to take it and do some basic checks. I have yet to see it, but I just intend to make sure the obvious th...

Yesterday

Hi I have a DX9 that I want to use as a master and a DX7S that I want to use as a Trainer slave. Th e DX9 is all set up as wing type Elevon-B I have bound the two transmit...
just like the title says. what do you guys set your alarm to? also what about flight pack voltage alarm for a 6s and 12s model or is this needed, any if it is why?
Hi I now feel an idiot in trying to use a 5v dc charger to temp replace dead batteries while using the FS-i6s with simulator. After the unit failed I check charger voltage (...
Guys, It seems that my charger has stopped recognizing my batteries. Just wanted to bounce my scenario off of you and see if anyone might know what is up: I'm trying to b...
Hello, I'm starting to think that it would be nice to have one of the newer radios that display RSSI and receiver battery voltage. My old Futaba 9C has been a very good rad...
GUys need a favor please, if you have this motor can you check my info ? I am getting 10 mm in circumference for the prop shaft dimension. The Hobby Parts specs show 8mm an...
I have always used a PC power supply to power up my DC 6 charger for all of our lipos for heli's and now cars. Recently the kids got a traxxas that came with a charger that pl...
Is it possible to hot up a TT46 Pro? I have not seen anything on this anywhere so i am guessing not. I know you can take the head gasket out and run no nitro but can the liner...

2 days ago

Using a Corona R6DM-SB with an XG8. Binding went fine and the TX is controlling the servos ok, just can't seem to get RX battery voltage telemetry to work. Checked Corona webs...
1 2 3 4 5 6 7 Next >>   25 50 75
 

Last videos:

3D Printed, Halbach Array Motor
3D Printed, Halbach Array Motor
For Mavic ,you should get one charger
For Mavic ,you should get one charger
For Mavic ,you should get one charger
For Mavic ,you should get one charger
For Mavic ,you should get one charger
For Mavic ,you should get one charger
For Mavic ,you should get one charger
For Mavic ,you should get one charger
Saito's New Engine: FG-90R3
Saito's New Engine: FG-90R3
Hey LIPO fans!
Hey LIPO fans!
LiPo Charge Help
LiPo Charge Help

Cars ·
Travel ·
Pets ·
production-frontend
We use cookies for navigation analysis and personalized advertisement. By using our site, you agree to our use of cookies. Learn more